[gpfsug-discuss] changing default configuration values
Aaron Knister
aaron.s.knister at nasa.gov
Mon Oct 9 19:56:25 BST 2017
Thanks! Good to know.
On 10/6/17 11:06 PM, IBM Spectrum Scale wrote:
> Hi Aaron,
>
> The default value applies to all nodes in the cluster. Thus changing it
> will change all nodes in the cluster. You need to run mmchconfig to
> customize the node override again.
>
>
> Regards, The Spectrum Scale (GPFS) team
>
> ------------------------------------------------------------------------------------------------------------------
> If you feel that your question can benefit other users of Spectrum Scale
> (GPFS), then please post it to the public IBM developerWroks Forum at
> https://www.ibm.com/developerworks/community/forums/html/forum?id=11111111-0000-0000-0000-000000000479.
>
>
> If your query concerns a potential software error in Spectrum Scale
> (GPFS) and you have an IBM software maintenance contract please contact
> 1-800-237-5511 in the United States or your local IBM Service Center in
> other countries.
>
> The forum is informally monitored as time permits and should not be used
> for priority messages to the Spectrum Scale (GPFS) team.
>
> Inactive hide details for Aaron Knister ---10/06/2017 06:30:20 PM---Is
> there a way to change the default value of a configuratiAaron Knister
> ---10/06/2017 06:30:20 PM---Is there a way to change the default value
> of a configuration option without overriding any overrid
>
> From: Aaron Knister <aaron.s.knister at nasa.gov>
> To: gpfsug main discussion list <gpfsug-discuss at spectrumscale.org>
> Date: 10/06/2017 06:30 PM
> Subject: [gpfsug-discuss] changing default configuration values
> Sent by: gpfsug-discuss-bounces at spectrumscale.org
>
> ------------------------------------------------------------------------
>
>
>
> Is there a way to change the default value of a configuration option
> without overriding any overrides in place?
>
> Take the following situation:
>
> - I set parameter foo=bar for all nodes (mmchconfig foo=bar)
> - I set parameter foo to baz for a few nodes (mmchconfig foo=baz -N
> n001,n002)
>
> Is there a way to then set the default value of foo to qux without
> changing the value of foo for nodes n001 and n002?
>
> -Aaron
>
> --
> Aaron Knister
> NASA Center for Climate Simulation (Code 606.2)
> Goddard Space Flight Center
> (301) 286-2776
> _______________________________________________
> gpfsug-discuss mailing list
> gpfsug-discuss at spectrumscale.org
> https://urldefense.proofpoint.com/v2/url?u=http-3A__gpfsug.org_mailman_listinfo_gpfsug-2Ddiscuss&d=DwICAg&c=jf_iaSHvJObTbx-siA1ZOg&r=IbxtjdkPAM2Sbon4Lbbi4w&m=PvuGmTBHKi7CNLU4X2GzUXkHzzezwTSrL4EdgwI0wrk&s=ma-IogZTBRL11_4zp2l8JqWmpHajoLXubAPSIS3K7GY&e=
>
>
>
>
>
>
> _______________________________________________
> gpfsug-discuss mailing list
> gpfsug-discuss at spectrumscale.org
> http://gpfsug.org/mailman/listinfo/gpfsug-discuss
>
--
Aaron Knister
NASA Center for Climate Simulation (Code 606.2)
Goddard Space Flight Center
(301) 286-2776
More information about the gpfsug-discuss
mailing list